International Journal of Metallurgy and Alloys

Correlation between full width at half maximum (FWHM) of XRD peak with mechanical properties

  1. Meghanshu Vashista ✉
  2. Mohd. Zaheer Khan Yusufzai

Abstract

Full width at half maximum (FWHM) of XRD profiles characterizes different mechanical properties. However, there is no literature available that discusses about the correlation between the FWHM of XRD peaks with mechanical properties (ultimate tensile strength, yield strength, strain hardening coefficient and micro-hardness) upon plastic deformation. Martensitic stainless steel (type 410) and Ferritic stainless steel (type 430) samples were plastically deformed under different strain rate using tensile testing machine. Variation in mechanical properties (ultimate tensile strength, yield strength, strain hardening coefficient and micro-hardness) with respect to strain rate was observed upon tensile testing of standard samples of both types of steels. The correlation between FWHM of XRD peak and mechanical properties was almost linear having good correlation coefficient. Keywords: X-ray diffraction (XRD), full width at half maximum (FWHM), mechanical properties

References (25)

  1. I.C. Noyan, J.B. Cohen, Residual Stress- Measurement by Diffraction and Interpretation, Springer-Verlag, New York, 1987
  2. Kim J. M., Chung H. T., Electrochemical characteristics of orthorhombic LiMnO2 with different degrees of stacking faults, Journal of Power Sources, 2003, 115 125–130
  3. Rai S., Choudhary B. K., Jayakumar T., Rao K. B. S., Raj B., Characterization of low cycle fatigue damage in 9Cr–1Mo ferritic steel using X-ray diffraction technique, International Journal of Pressure Vessels and Piping, 1999, 76, 275–281
  4. Tung H. M., Huang J. H., Tsai D. G., Ai C. F., Yu G. P., Hardness and residual stress in nanocrystalline ZrN films: Effect of bias voltage and heat treatment, Materials Science and Engineering A, 2009, 500, 104–108.
  5. Quesnel, D. J., Meshii, M., Cohen, J. B., Residual stress in high strength low alloy steel during low cycle fatigue, Material Science and Engineering, 1978, 36, 207– 215.
  6. Goto, T., Material strength evaluation and damage detection by X-ray diffraction, In: Barrett CS, editor. Advancement in X-ray Analysis, 23A. New York: Plenum Press, 1992. pp. 489.
  7. Ozdemir A.T., Edwards L., Relaxation of residual stresses at cold worked fastener holes due to fatigue loading. Fatigue Fracture Engineering and Material Structure 1997, 20(10), 1443–145
  8. Ping Z. Z., Yu-hong Q.I., Deni D., Gerard B., Microstructure Variation and Hardness Diminution During Low Cycle Fatigue of 55NiCrMoV7 Steel, Journal of Iron and Steel Research, International, 2007,14(6) : 68-73
  9. Shariati M., Ghoranneviss M., Hosseini H., Hantehzadeh M. R., Effect of annealing temperature on properties of Al–Cu–N thin films deposited by DC magnetron sputtering, Surface and Coatings Technology, 2007, 201, 5570–5573
  10. Lee Y.C., Hu S. Y., Water W., Huang Y. S., Yang M. D., Shen J. L., Tiong K. K., Huang C. C., Improved optical and structural properties of ZnO thin films by rapid thermal annealing, Solid State Communications, 2007, 143, 250–254
  11. Lee Y. C., Hu S.Y., Water W., Tiong K. K., Feng Z. C., Chen Y. T., Huang J. C., Lee J. W., Huang C. C., Shen J. L., Chen M. H., Rapid thermal annealing effects on the structural and optical properties of ZnO films deposited on Si substrates, Journal of Luminescence, 2009, 129, 148–152
  12. Elilarassi R., Chandrasekaran G., Effect of annealing on structural and optical properties of zinc oxide films, Materials Chemistry and Physics, 2010 121, 378–384
  13. Chen N., Yao K. F., Ruan F., Yang Y. Q., The influence of cooling rate on the hardness of Pd–Si binary glassy alloys, Materials Science and Engineering A, 2008, 473, 274–278
  14. Sudhakar S., Ganesh V., Nagarajan M., Kulriya P. K., Sulania I., Avasthi D. K., Asokan K., Baskar K., Structural and surface characteristics of room temperature and low temperature swift heavy ion implanted InAs and InSb wafers, Nuclear Instruments and Methods in Physics Research B, 2008, 266, 1723–1728
  15. Dang S. E., Zhang G., Li Z. Y., Yan Z. J., Li Y. T., Liang W., Variation of microstructure of Zr60Al15Ni25 bulk amorphous alloy during rolling at room temperature, Journal of Alloys and Compounds, 2009, 479 L15–L17
  16. Vashista M., Paul S., Correlation between surface integrity of ground medium carbon steel with Barkhausen Noise parameters and magnetic hysteresis loop characteristics, Materials & Design, (2009), Vol. 30, pp.1595–1603
  17. Vashista M., Paul S., “Correlation between full width at half maximum (FWHM) of XRD peaks with residual stress on ground surfaces” Philosophical Magazine, Vol. 92, No. 33, pp. 4194-4204, (2012)
  18. Pariente I. F., Guagliano M., About the role of residual stresses and surface work hardening on fatigue ΔKth of a nitrided and shot peened low-alloy steel, Surface & Coatings Technology, 2008, 202, 3072–3080
  19. Choung, J. M. and Cho, S. R., Study on true stress correction from tensile tests, Journal of Mechanical Science and Technology 22 (2008) 1039-1051
  20. G!alvez D.F., P!erez, J.R., G!alvez V.S., The spalling of long bars as a reliable method of measuring the dynamic tensile strength of ceramics, International Journal of Impact Engineering 27 (2002) 161–177
  21. Soliman, M. A., Kinawy, N., Eleiwa, M. M., Study on the fracture process of aluminium under tensile creep test, Journal of Materials Science Letters 5 (1986) 329-330
  22. Balart M. J., Bouzina A., Edwards L., Fitzpatrick M.E., The onset of tensile residual stress in grinding of hardened steels. Materail Scienec and Engineering, 2004;367: 132–42.
  23. Lindgren, M., Lepisto, T., Effect of prestraining on Barkhausen noise vs. stress relation, NDT&E International, (2001), Vol. 34, No. 5, pp. 337–344.
  24. Poggie R. A., Wert J.J., The influence of surface finish and strain hardening on near-surface residual stress and the friction and wear behaviour of A2, D2 and CPM-10V tool steels, Wear, 1991;149:209–20.
  25. Cullity, B. D. (1978), Element of X-ray diffraction, Addison Wesley Publishing Company, USA, Second edition.

Read more of it

Subscribe to one journal or build your own list of several. One invoice, one payment, access for a full year.

Subscribe to journals →

Publish your article

Peer-reviewed journals across every subject, with open access options. Send your manuscript to the right editor today.

Publish with us → Calculate your APC
Support