Search
830 articles for “cost”
-
Design and Pinch Analysis of Styrene Production Process Using Aspen HYSYS and Aspen Energy Analyzer
Abstract: This paper presents the design and energy analysis of styrene production process. Process flow diagram is designed using Aspen HYSYS. Styrene product obtained is of purity 73% and further purity is recommended. Pinch analysis is applied to the process plant by using Aspen Energy Analyzer, as a part of that in the first step all the stream data is extracted, in the second step heat exchanger networks (HEN) is developed …
Published in International Journal of Chemical Synthesis and Chemical Reactions · Vol. 1, Issue 1, 2015 Read article
-
Deciphering Foam: Exploring Antifoaming Agents and Their Mechanism
Abstract: Antifoaming agents are critical additives employed in industrial processes to counter foam formation, which can hinder efficiency and cause equipment damage. These agents, available in various formulations like silicone-based, mineral oil-based, and polyethylene glycol-based, are selected based on specific foam properties and operating conditions. Choosing the right antifoam agent is crucial, with silicone-based ones often preferred for their stability and effectiveness across different pH levels and temperatures. Conversely, mineral oil-based …
Published in International Journal of Chemical Synthesis and Chemical Reactions · Vol. 9, Issue 2, 2023 · pp. 32–36 Read article
-
Energy Conservation with use of Cool Roof Coatings
Abstract: Regions with hot and dry climate often experience very high levels of solar radiation, high ambient temperatures and relatively low specific humidity. The roofs of buildings in such areas are always exposed to Sun for long duration during the daytime. Solar radiation is responsible for heat transfer through the building roof. Actually, Solar radiation heat the roof which in turn reradiates the heat onto the ceiling and finally on to …
Published in International Journal of Renewable Energy and its Commercialization · Vol. 2, Issue 2, 2016 · pp. 1–13 Read article
-
Solar Power – A Renewable Energy and Alternate Energy Sources
Abstract: Renewable energy is sustainable as it is obtained from sources that are inexhaustible (unlike fossil fuels). Renewable energy sources include wind, solar, biomass, geothermal and hydro, all of which occur naturally. Renewable energy, generally speaking, is clean energy and non-polluting. Many forms do not emit any greenhouse gases or toxic waste in the process of producing electricity. It is a sustainable energy source that can be relied on for the …
Published in International Journal of Renewable Energy and its Commercialization · Vol. 3, Issue 2, 2017 · pp. 8–14 Read article
-
Effect of Environmental Parameters on Corrosion of Metal Steel in Stagnant Fresh Water Using Finite Element Approach
Abstract: Corrosion as the determination or destruction of metal due to the reaction with it environment has posed a large amount of threat to industrial plants, human, increased cost of maintenance of plant and like cause injury to human due to accident in work place. This work studies the effect of environmental parameters of corrosion of three types of steel, Cast iron, mild steel and stainless steel in stagnant water media …
Published in International journal of Thermodynamics and Chemical Kinetics · Vol. 6, Issue 1, 2020 · pp. 1–23 Read article
-
Thermodynamic Optimization of Renewable Energy Processes
Abstract: In the pursuit of sustainable energy solutions, the thermodynamic optimization of renewable energy processes plays a crucial role in enhancing efficiency and reducing environmental impact. This paper explores the principles and methodologies involved in optimizing various renewable energy systems, including solar, wind, biomass, and geothermal energy. By leveraging the fundamentals of thermodynamics, the study examines key parameters and performance indicators to identify optimal operating conditions and design configurations. The analysis …
Published in International journal of Thermodynamics and Chemical Kinetics · Vol. 9, Issue 2, 2023 · pp. 31–37 Read article
-
Construction Claims’ Impacts on Project Performance Baselines
Abstract: Nowadays claims in construction projects became usual and expected during the construction procedure. In addition, claims are the most disruptive and unpleasant events of construction projects because of their impacts on project final cost and scheduled completion date. This study, as one of chain researches on construction claim management (the other researches were directed to study types of claims, the causes and the best management approach to prevent their impacts), …
Published in International Journal of Construction Engineering and Planning · Vol. 1, Issue 1, 2015 · pp. 14–20 Read article
-
A Study on Mechanical Properties and Fracture Behavior of Chopped Fiber Reinforced Self-Compacting Concrete
Abstract: The development of self-compacting concrete (SCC) is innovatory landmark in the history of construction industry resulting in predominant usage of SCC worldwide nowadays. It has many advantages over normal concrete in terms of enhancement in productivity, reduction in labor and overall cost, excellent finished product with excellent mechanical response and durability. Further, incorporation of fibers enhances its properties specially related to post crack behavior of SCC. Hence, the aim of …
Published in International Journal of Construction Engineering and Planning · Vol. 3, Issue 1, 2017 · pp. 90–122 Read article
-
SUMMERIZING STRUCTURE AND FUNCTION OF FORMWORK IN MULTI STORIED RCC BUILDING
Abstract: The formwork system of floor slab is an important element in construction of multi-storied RCC buildings which governs the duration and cost of construction. The formwork and shoring structure does not extend to the foundation after the first few slab levels. Generally the formwork and back propping of one or two levels is provided. The research articles give insight on various technical parameters (slab shore load distribution, age of concrete, …
Published in International Journal of Construction Engineering and Planning · Vol. 8, Issue 1, 2022 · pp. 1–8 Read article
-
An Experimental Study on Concrete by Replacement of Coarse Aggregate with Demolished Building Waste in Crushed Concrete
Abstract: A large amount of construction and demolition wastes are produced annually in India. These waste materials require a large place to dispose and then the disposal of wastes has become a severe problem. The continuous use of natural resources for making conventional concrete leads to the reduction in their availability and results in the increase of the cost of the coarse aggregate and fine aggregate. The possible use of recycling …
Published in International Journal of Concrete Technology · Vol. 4, Issue 1, 2018 · pp. 25–28 Read article
-
Effect of Fly Ash on Compressive Strength of Mortar and Brick Aggregate Concrete
Abstract: This paper presents tse influence of fly ash on compressive strength of mortar and brick aggregate concrete. A lot of tests were done about strength of fly ash concrete all over the world. In those experiments, stone chips were generally used as coarse aggregate. In this experiment locally available materials such as burnt clay brick chips as coarse aggregate, sand and fly ash available in Bangladesh (Indian fly ash) were …
Published in International Journal of Concrete Technology · Vol. 7, Issue 1, 2021 · pp. 7–23 Read article
-
Mechanical Behavior of Fly Ash Concrete A Critical Review
Abstract: Concrete structure is the most common all over the world. Cement is the major ingredient of concrete. Though the raw materials needed for manufacture of cement are available in most parts of the world, many countries have severe shortage of cement, although their needs are vast. The search for suitable substitute for cement, either partially or fully, has thus become a challenge for planning the development of many of the …
Published in International Journal of Concrete Technology · Vol. 7, Issue 1, 2021 · pp. 29–43 Read article
-
Effect of Temperature on mechanical properties of Geopolymer concrete: A Review
Abstract: Concrete is the most widely used material after water in building and construction field. It is the oldest man-made material and is easily available for use at cheaper costs. This material is causing harm to environment on mass extent. OPC i.e. Ordinary Portland Cement is second contributor after automobile industry in Carbon Dioxide emission. This review presents the study of replacement of regular concrete cement with cementitious material like fly …
Published in International Journal of Concrete Technology · Vol. 7, Issue 1, 2021 · pp. 24–28 Read article
-
Experimental Study on Behavior of various FRP on strength properties of concrete
Abstract: Fibre sheeting is an effective way to repair structures that have become essentially fragile greater than their living expectancy. A lot of research is currently being done on the use of fibre sheets and overlays all around the world. In comparison to traditional repair frameworks and materials, FRP frames are a more cost-effective option. The purpose of this study is to experimentally investigate the behavior of GFRP, CFRP, and BASALT …
Published in International Journal of Concrete Technology · Vol. 8, Issue 2, 2022 · pp. 9–13 Read article
-
Condition Assessment of Structures Using Vibration Technique
Abstract: Structural Health Monitoring grasps the Promise for enhancing the structural performance with an outstanding cost/benefit ratio. Condition assessment is a technique used in health monitoring in the damage detection, to ensure the serviceability and the durability of the structures. In the present report, condition assessment of the structures using low frequency technique is being completed through experimental modal analysis and computational analysis software ANSYS 9.0 over structural elements beam and …
Published in International Journal of Geological and Geotechnical Engineering · Vol. 3, Issue 1, 2017 · pp. 36–46 Read article
-
Evaluation of RC Frames in Shifting on Seismic Zone 3 to 5 and Retrofitting Techniques using ETABS
Abstract: The finite element analysis has been carried out on six storey reinforced concrete frames using commercial finite element software ETABS. The performance of six storeys infilled frame failing due to improper design as well as inadequate reinforcements when seismic zone shifting from zone 3 to 5 was studied. The behavior of infilled frame considered in zone 5 was studied and compared with the results obtained from the analysis of frame …
Published in International Journal of Structural Engineering and Analysis · Vol. 3, Issue 2, 2017 · pp. 1–16 Read article
-
Comparative Study on Reinforced Cement Concrete Structures and Concrewall Structures
Abstract: Developing countries especially those in India, are facing the challenge of a growing middle class with greater demand for housing facilities. Faster and more affordable methods of construction are being sought after it, more than ever before as the action of emergency response. Increased innovation aimed at reducing the cost of construction, and creating affordable housing, is being integrated into methods of building and construction. This has led to introduction …
Published in International Journal of Structural Engineering and Analysis · Vol. 5, Issue 2, 2019 · pp. 8–11 Read article
-
Deterministic Analysis of Multilevel Structure with Geometric Non- Linearity
Abstract: After the invention of numerous Structural analyses software, there has been rapid changes in the analysis of multi-storey structures and skyscrapers. These software allows the designers and engineers to forecast precisely the critical elements of the design and the points to be reinforced before the actual construction of the structure.For the critical analysis, software utilizes the Geometric Non-linearity method which is one of the second order analysis. This is also …
Published in International Journal of Structural Engineering and Analysis · Vol. 7, Issue 1, 2021 · pp. 11–15 Read article
-
Seismic Analysis of G+10 Storey Building Using Structural Light weight and Normal Weight Concrete
Abstract: Concrete is considered a slight weight concrete which has density of less than 2000 kg/????3. The Structural Lightweight Concrete (SLWC) is mainly used to reduce the dead load of concrete structure. The purpose of this research is to examine and compare the results of Structural lightweight concrete by adding perlite with Normal Weight Concrete multistorey building. Often these multistorey buildings are constructed of ordinary concrete, steel, and other materials, and …
Published in International Journal of Structural Engineering and Analysis · Vol. 8, Issue 2, 2022 · pp. 1–19 Read article
-
BY USING ETABS ANALYSIS OF LATERAL RESISTANCE SYSTEM TO REDUCING THE DISPLACEMENT IN MULTISTOREY BUILDING
Abstract: It is usually a good idea to build a huge building to make better use of the land Recycled concrete is predominantly employed in both workplaces and homes. However, tall structures are susceptible to collapse, especially when subjected to seismic activities and wind vibrations. The structure is subjected to high tension and displacement of lateral forces and can withstand vertical forces with adequate stiffness for horizontal forces. The stability of …
Published in International Journal of Structural Engineering and Analysis · Vol. 9, Issue 1, 2023 · pp. 21–37 Read article