Search
148 articles for “tensile properties”
-
Innovative Concrete Composites: Assessing Mechanical Strength with Fly Ash, Glass, and Granite Waste Incorporation
Abstract: Waste management poses a significant challenge for countries in both current and future contexts. The generation of solid waste from various industries, such as stone, glass, coal, and tires, constitutes a major issue in India, leading to significant environmental and health concerns for the surrounding population. This study addresses these challenges by exploring the utilization of waste granite and glass powder as materials to replace sand and cement, respectively, with …
Published in International Journal of Construction Engineering and Planning · Vol. 9, Issue 2, 2023 · pp. 37–45 Read article
-
Experimental Investigation of FSW on Al 6061-T6 MG Dissimilar Joints
Abstract: Friction Stir Welding (FSW) is a solid-state joining technique that has shown significant potential for welding dissimilar materials, such as aluminum and magnesium alloys, which are difficult to join using conventional fusion welding methods due to large differences in their physical, thermal, and metallurgical properties. During FSW, contact between the rotating, wear-resistant tool shoulder, the pin, and the work piece produces frictional energy. Additional thermal energy develops because of intense …
Published in International Journal of Manufacturing and Materials Processing · Vol. 12, Issue 2, 2026 · pp. 1–12 Read article
-
Evaluating the Rate of Response on Asphalt Concrete Mix Permeability Influenced by Non-Bituminous Modifier on Light Traffic
Abstract: Characterization of material property is fundamental in the Mechanistic-Empirical design of flexible pavement. One such key material property is the stiffness of the pavement these influences tensile strain levels and is imperative for either the determination or pavement cracking synonymous with pavement life. It is on this basis, that the present study explored techniques that will improve the performance of flexible road pavement by modifying its stiffness; dynamic modulus, E* …
Published in International Journal of Transportation Engineering and Traffic System · Vol. 4, Issue 1, 2018 · pp. 33–39 Read article
-
Effects of Reinforcing Elements in Soil Reinforcement
Abstract: The inclusion of reinforcing elements in a soil mass improves its geotechnical properties. The principle behind soil reinforcement is that the reinforcing elements absorb the tensile load and shear stress within the reinforced structures and hence prevent the shear failure and settlement. The friction developed between the interface of soil and reinforcing element improves the properties of soil. Different types of natural and synthetic fibers have been used in various …
Published in International Journal of Geological and Geotechnical Engineering · Vol. 6, Issue 2, 2020 · pp. 22–33 Read article
-
Concrete Properties Enhancement with use of Carbon Fibers
Abstract: Concrete standard grade of concrete with high strength with mechanical properties like flexural strength as well as split is a requirement / need for today’s fastest construction work. To improve the mechanical properties there is need for adding fibers in concrete. Distinct fibers available in worldwide out of which carbon fibers had showed very effective solution for enhancing high strength mechanical properties of concrete. In this paper we have designed …
Published in International Journal of Geological and Geotechnical Engineering · Vol. 7, Issue 2, 2021 · pp. 1–8 Read article
-
Analyzing Strength Properties of Self-Compacting Concrete at Elevated Temperatures
Abstract: This study investigates the influence of fly ash substitution for Ordinary Portland Cement (OPC) on the compressive and splitting tensile strengths of Self-Compacting Concrete (SCC) mixes. The findings reveal that while early age strength may decrease with fly ash substitution, strategic material selection, such as incorporating foundry sand, mitigates this decline. Satisfactory fresh properties were achieved across SCC mixes labeled SCC1-SCC4, with compressive strengths ranging from 30.49 to 19.19 MPa …
Published in International Journal of Concrete Technology · Vol. 10, Issue 1, 2024 Read article
-
A Study on Stress Analysis of Aluminum Alloy Solidified in Metallic Molds
Abstract: Abstract The casting technique is regarded as the primary manufacturing process. It has several process parameters that affect the cast structure. Mold geometry is considered one of the most important metal parameters to cast. In the current work, the influence of mold geometries on mechanical properties (deformation and stress concentration) of liquid Aluminum alloy solidified in the steel mold is assessed using ANSYS simulation software. Molds were subject to a …
Published in International Journal of Manufacturing and Materials Processing · Vol. 10, Issue 2, 2024 · pp. 10–15 Read article
-
Impact of Additives on the Split Tensile Strength of Roller Compacted Concrete
Abstract: Additives are implemented as partial replacement of Portland cement in concrete to enhance the required physical properties. In the present investigation, roller compacted concrete slab samples were prepared using gap and dense aggregate gradation. Three percentages of Portland cement were adopted, (16, 12, and 10) % by weight of aggregates. Three types of additives, (hydrated lime, fly ash, and fumed silica) were implemented as partial substitute of Portland cement. Core …
Published in International Journal of Concrete Technology · Vol. 7, Issue 2, 2021 · pp. 9–15 Read article
-
Microstructural and Mechanical Behavior of Al6082/SiC/Gr Hybrid Composites
Abstract: The aim involved in designing metal matrix composite materials is to combine the desirable attributes of metals and ceramics. The present work is focused on the study of behavior of aluminum alloy (Al6082) with SiC and graphite (Gr) composites produced by the stir-casting technique. The reinforcement percentage is varied from 5% to 15% in a step of three. Microstructure test, tensile test, and hardness tests are performed on the samples …
Published in International Journal of Manufacturing and Materials Processing · Vol. 5, Issue 2, 2019 · pp. 28–40 Read article
-
Mechanical properties of Poly vinyl alcohol and Nitrocellulose blends.
Abstract: Mechanical properties of polyvinyl alcohol and nitrocellulose blends has been determined successfully via tensile strength, Young’s modulus, percentage elongation and impact strength. The blends of the respective polymers are in the ratio PVA:NC (90:10,80:20,60:40,50:0,40:60,10:90). There are good results from different blend ratios which include tensile strength PVA: NC 90:10 (16.98MPa) Young’s modulus 60:40 (0.71MPa). The highest percentage elongation was observed for 80:20 at 160.09%. The most elastic blend ration was …
Published in International Journal of Analytical and Applied Chemistry · Vol. 6, Issue 1, 2020 · pp. 54–59 Read article
-
Recycling Multilayer Materials: Discovering Mechanical Parameters for Engineering Applications
Abstract: Multilayer materials have been widely used in various applications such as packaging, electronics, and construction industries. However, the disposal of these materials is becoming a significant environmental concern due to their non-biodegradable nature. Therefore, the recycling of multilayer materials has become an essential aspect of sustainable waste management. The mechanical characteristics of materials recycled from multilayer products were examined in this study. The focus was on determining the impact of …
Published in International Journal of Metallurgy and Alloys · Vol. 8, Issue 2, 2022 · pp. 43–47 Read article
-
Thermo-Mechanical Properties of Banana and Jute Fiber Reinforced Polypropylene Composites
Abstract: Abstract Present research aims at finding out better fiber reinforcement for low cost and eco-friendly polymer matrix composite. Polypropylene was chosen as a matrix, while jute and banana fiber were chosen as reinforcement. Composites were prepared by using a hot press machine. Fiber loading was varied at 0, 4 and 8 volume%. Both raw jute and banana fiber was chemically treated with 5 wt% sodium carbonate and composites were also …
Published in International Journal of Composite Materials and Matrices · Vol. 5, Issue 2, 2019 · pp. 37–47 Read article
-
Multiple Regression Analysis of Compressive, Flexural, and Split Tensile Strength in M40 Grade Concrete
Abstract: Concrete plays a key role as a construction material across the globe. The strength parameters of the concrete are primary reason for which it is designed for. The design mixed concrete has multiple strength parameters like compressive strength, spilt tensile strength, flexural (bending) strength etc. For each newly design mixed concrete, the mentioned strength parameters are tested for various time duration like 3 days, 7 days, 14 days, 28 days …
Published in International Journal of Construction Engineering and Planning · Vol. 11, Issue 2, 2025 · pp. 20–34 Read article
-
Mechanical properties of Al-Si17Cu3.5Mg0.8 alloy fabricated by stir casting with UV and new CRSS casting process with and without T6 condition
Abstract: Aluminum-Silicon metal matrix composites are the popular materials in the vast majority of the car and modern industries on account of their low weight, high mechanical properties, and incredible wear opposition properties. In the present study, Al-Si17Cu3.5Mg0.8 alloy is fabricated by two casting processes such as stir casting with ultrasonic vibrations (RSC) and merged-rheo-stir-squeeze (CRSS) casting with and without heat treated (T6) condition. Microstructural and material characterization was explored by …
Published in International Journal of Metallurgy and Alloys · Vol. 6, Issue 1, 2020 · pp. 15–24 Read article
-
Experimental Investigation To Study the Effect of Heat Treatment on Mechanical Properties and Microstructure of Duplex Stainless Steel
Abstract: The broad aim of this paper is to study the enhancement in mechanical properties of duplex steel by thermomechanical processing. Solution annealing followed by water quenching, hot rolling to 10% and 30%, cryo-rolling to 80% and 90% and ageing at 600°C and 1000°C for 5 hrs were the treatments given. The cryo-rolled samples were used for impact testing and rest for tensile testing. Microstructural analysis was done after the various …
Published in International Journal of Mechanics and Design · Vol. 2, Issue 2, 2016 · pp. 32–42 Read article
-
Mechanical Behavior of Calotropis Gigantea FruitBunch Fiber-Epoxy Composites
Abstract: Global warming solutions in the modern era are centered on substituting environmentally friendly biodegradable materials for fossil fuels to slow down the rate at which they are being depleted. The study literature supports the use of substitute materials for plastics in the creation of composite materials, and this work envisions the use of Calotropis gigantea fruit bunch fiber as one such substitute material. Since Calotropis gigantea fruit bunch fiber is …
Published in International Journal of Composite Materials and Matrices · Vol. 10, Issue 2, 2024 · pp. 45–58 Read article
-
To Study Mechanical Properties of Concrete by Using Industrial Waste Material
Abstract: Concrete is a very important material with cement, water, aggregate and admixture as contents. Due to increasing pollution and demand of concrete, its production should be environmental friendly. In this study, we emphasize on environment friendly concrete. The proportion of silica fume was as follows: add 3%–15% in interval of 3% by weight of cement in concrete and fly ash was add 5%–25% in interval of 5% by total weight …
Published in International Journal of Construction Engineering and Planning · Vol. 5, Issue 1, 2019 · pp. 18–27 Read article
-
Influence of Different Quenching Media on the Mechanical Properties of Mild Steel – A Case Study of Coconut Oil, Mineral Oil, Jatropha Oil, and Water
Abstract: This study elucidates how local cooling agents, such as coconut oil and jatropha oil, influence the mechanical characteristics of heat-treated mild steel. Tensile testing, Brinell hardness testing, and microstructural analysis were conducted on both heat-treated and untreated samples. The results show observable differences in the heat-treated materials’ mechanical characteristics. Specifically, the yield strength increased across all quenched media, while the ultimate tensile strength decreased for samples cooled with coconut oil …
Published in International Journal of Metallurgy and Alloys · Vol. 10, Issue 2, 2024 · pp. 1–8 Read article
-
An Investigation into the Mechanical and Strength Properties of Rubberized Asphalt Concrete
Abstract: In this study, the suitability of large rubber chunks from shredded tires as aggregates in cold mixes for road construction is investigated. The rubber was used as an additive to the asphalt binder. Thirty percent of rubber by weight was introduced into the binder at a higher temperature and the rubber was allowed to react with the binder. It was shown among other findings that for various particle sizes, the …
Published in International Journal of Transportation Engineering and Traffic System · Vol. 4, Issue 1, 2018 · pp. 11–16 Read article
-
Improvement of mechanical properties of recycled polyethylene with utilization of bio-filler
Abstract: Nowadays, the consumption of plastics all over the world has been tremendously growing, which is culminating into large amount of waste plastic material. It is believed that the management of solid waste is one of the major environmental concerns in the world. Due to limited space on landfills and increasing costs of plastics, utilization of waste plastics has become an attractive alternative for disposal. This research work describes the preparation …
Published in International Journal of Green Chemistry · Vol. 3, Issue 1, 2017 · pp. 18–26 Read article