Search
1495 articles for “work”
-
Minimal Reduction of Fuel Consumption and Pollution with the Performing a New Design of Flat Engines by Simulation
Abstract: The automotive engine is one of the most important performance of the automotive today and has the task of transmitting power to the gearbox. That is why the world’s largest automotive companies are trying to produce engines that have the maximum power and the lowest fuel consumption. In this article, a motor design with a different appearance was presented. If we want to attribute the design of this engine to …
Published in International Journal of Mechanics and Design · Vol. 7, Issue 1, 2021 · pp. 17–21 Read article
-
Gas turbines - A review
Abstract: Gas-turbine engines are any internal combustion engines that use gas as the working fluid to turn a turbine. Additionally, this phrase also refers to an entire internal combustion engine, which must have a turbine, a combustion chamber, and a compressor. Power generation with gas turbines dates back to 1939.One of the most often utilised power generation systems today is the gas turbine. The compressor, the combustion chamber The turbine, combustor …
Published in International Journal of Mechanics and Design · Vol. 8, Issue 1, 2022 · pp. 21–24 Read article
-
Arduino Based Sun Tracking System
Abstract: The main objective of this project is to create an Arduino-compatible, extremely accurate solar tracker. The location of the sun was sensed in this work in two stages, primary and secondary. The sun-Earth relationship is used in the first stage of indirect sensing as a coarse adjustment, and a set of four LDR sensors is used in the second stage of direct sensing as output tuning to adjust the azimuth …
Published in International Journal of Mechanics and Design · Vol. 8, Issue 2, 2022 · pp. 25–32 Read article
-
Robotic Path: Analysis of Algebraic Topological Properties of Stream Lines Due to Source-Sink, Dipole and Vortex
Abstract: The importance of robotic path planning cannot be overstated. Robotic path planning plays a crucial role in ensuring efficient and safe navigation for robots. It enables robots two autonomously determine the most optimal path to reach their destination while avoiding of obstacles and potential collisions. By carefully analyzing the environment and considering various factors such as distance, speed, and obstacles, robotic path planning enhances the overall performance and productivity of …
Published in International Journal of Mechanics and Design · Vol. 9, Issue 2, 2023 · pp. 1–8 Read article
-
Review on the Enhancing the Heat Transfer Rate in the Air Heater by Modifying the Design
Abstract: An overview of the research on air heat exchangers and solar air heaters is given in this work. The goal of the review is to promote discussion and evaluation of the researchers' results. The paper includes extensive descriptions of several types of air heaters, air heat exchangers employing electrical heaters and other technologies, and solar air heaters with different absorber plate surface geometries to increase the rate of heat transfer. …
Published in International Journal of Mechanics and Design · Vol. 9, Issue 2, 2023 · pp. 27–32 Read article
-
Investigation on the influence of calcium Fluoride and Barium Fluoride on cutting performance during hard turning with minimal fluid application
Abstract: Recently the concept of minimal fluid application has gained attention in metal cutting industry as it has the ability to resemble pure dry turning and at the same time free from all the problems related to large scale use of cutting fluid as in conventional wet turning. Since a very small quantity of cutting fluid is doing cooling and lubrication in minimal fluid application, there must be some performance enhancers …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 2, 2016 · pp. 17–26 Read article
-
Modeling of 6 DOF Shake Table and Its Control
Abstract: This paper focuses on the modeling of 6 DOF shake table and implementation of controller and inverse kinematics. Shake tables are widely used to validate the structural integrity and reliability of a specimen during earthquake. Hence shake tables are used to simulate the acceleration spectra of earthquake. Modeling helps to analyze the system and its parameters for better understanding. The inverse kinematics are developed using degree of freedom (DOF) control …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 2, 2016 · pp. 56–60 Read article
-
Multi-class Fault Diagnosis of Rolling Element Bearing Based on Empirical Mode Decomposition and Entropy Features
Abstract: Rolling element bearings are one of the most commonly used machine elements in engineering industry. Fault detection and diagnosis of rolling element bearings is essential for prevention of malfunction and failure during operation. The present work deals with rolling element bearing fault diagnosis by using Support Vector Machine (SVM) and Artificial Neural Network (ANN). Four types of bearing conditions are considered in the present analysis: inner race fault (IR), outer …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 1, 2016 · pp. 01–10 Read article
-
Review of Optimization Process Parameters in Welding system
Abstract: This study was based on design of experiment (DOE) using Taguchi method with four welding parameters namely welding current, welding speed, root gap and electrode angle considered for experimentation. An orthogonal array of L9 experimental design was adopted and ultimate tensile strength was investigated for each experimental run. The tensile test was carried out on extracted welded and unwelded specimens using universal testing machine (UTM). Microstructures of the welded specimens …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 1, 2016 · pp. 48–54 Read article
-
Risk Assessment And Analysis In A Chemical Industry
Abstract: Chemical manufacturing sector in India is well established and has recorded a steady growth in the overall industrial scenario .The chemical and the allied industries are among the faster growing segments of Indian industry. The risks associated with the chemical industry are commensurate with their growth. Apart from their utility, chemicals have their own inherent properties and hazards like flammable, explosive, toxic or corrosive etc. Several major accidents had occurred …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 1, 2016 · pp. 57–64 Read article
-
Optimization of Machining Parameters for Nylon 6 Composite in CNC Lathe Using PCA-Based TOPSIS
Abstract: This work investigates the parametric optimization of CNC turning operation for Nylon 6 with principal component analysis (PCA) and technique for order preference by similarity to ideal solution (TOPSIS) based on Taguchi approach. Taguchi’s L16 orthogonal array takes 16 experimental runs to execute the design matrix of turning parameters through PCA coupled with TOPSIS, utilizing relevant experimental data as obtained through experimentation. Turning speed (TS), feed rate (FD) and depth …
Published in International Journal of Manufacturing and Materials Processing · Vol. 4, Issue 1, 2018 · pp. 36–47 Read article
-
Manufacturing of Reinforced Composite Fly Ash Bricks – Product Analysing and Development Using Value Engineering Techniques
Abstract: The key driver of Indian economy is structured by the infrastructure development. This sector is principally responsible for thrusting India’s overall development and an intensive focus from government for initiating policies that would propose alternate methods and materials for which the end products ensuring high quality, non-degradable, time-bound creation of world class infrastructure in the country. Infrastructure sector includes power, bridges, dams, roads, and urban infrastructure development, which requires huge …
Published in International Journal of Manufacturing and Materials Processing · Vol. 4, Issue 1, 2018 · pp. 12–19 Read article
-
Experimental Investigation of MRR and Surface Finish Using Abrasive Jet Machining of Aluminum Alloy 7475
Abstract: In this thesis, different experiments are performed on aluminum alloy 7475 by varying various parameters such as pressure, sand feed, transverse speed and standoff distance, i.e. nozzle-to-work-piece distance to determine material removal rates and surface finish. Optimization is done using L9 orthogonal array by Taguchi technique to determine better parameters to obtain maximum removal rates and minimum surface roughness. The parameters considered are transverse speed 50, 100, 150 mm/min; standoff …
Published in International Journal of Manufacturing and Materials Processing · Vol. 4, Issue 1, 2018 · pp. 20–31 Read article
-
Experimental Study and Analysis of Coefficient of Friction for Mild Steel Under Various Lubrication Conditions
Abstract: The coefficient of friction plays decisive role in the metal-forming processes. This study focuses on determination of the coefficient of friction between work piece and lubricants using ring compression test by experiments physical modeling and finite element (FE) simulation. A series of ring compression tests were carried out to obtain friction coefficients of mild steel under lubricants including boric acid, Vaseline, grease and dry conditions. According to Male and Cockcroft …
Published in International Journal of Manufacturing and Materials Processing · Vol. 4, Issue 2, 2018 · pp. 34–42 Read article
-
Effect of Pulsed Current Micro Plasma Arc welding parameters on Mechanical properties AISI 304 and AISI 430 dissimilar weld joint
Abstract: In the present work, two dissimilar AISI 304 and AISI 430 sheets of 0.4mm thick welded using Micro Plasma Arc Welding. Welding input parameters like peak current, base current, pulse rate and pulse width are considered and output responses like fusion zone grain size, hardness and ultimate tensile strength of the welded joint are considered. 31 experiments are performed as per Central Composite Design (CCD) design matrix of Response Surface …
Published in International Journal of Manufacturing and Materials Processing · Vol. 5, Issue 1, 2019 · pp. 1–26 Read article
-
Application of Response Surface Method in Studying the Properties of Micro-plasma Arc Welded AISI 904L Super Austenitic Steel
Abstract: Super austenitic steels play a major role in fabrication of corrosion resistance components which are subjected to severe corrosion. In the present work, super austenitic steel AISI 904L of 0.4 mm thickness is butt welded using Micro Plasma Arc Welding. Welding input parameters like peak current, base current, pulse rate and pulse width are considered and output responses like fusion zone grain size, hardness and ultimate tensile strength of the …
Published in International Journal of Manufacturing and Materials Processing · Vol. 5, Issue 2, 2019 · pp. 1–17 Read article
-
Characterization of Tensile Properties of Dissimilar Welded Joints of 316 Stainless Steel and HSLA Steel
Abstract: In this research, dissimilar weld joints of 316 stainless steel/HSLA steel were produced using ER316L-16 and E7018 filler metals by varying welding parameters such as current and arc voltage. Heat input and travel speed was computed. The joints were subjected to tensile test and tensile values were determined, computed, recorded and analysed. The heat inputs were compared with the tensile test results. According to the results obtained and analysis carried …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 2, 2020 · pp. 1–7 Read article
-
Analysis of Mechanical Attributes of Nano clay Reinforced Polymer Composites
Abstract: Composite material provide a Higher and unique mechanical and physical attributes because of its combines the most unique attributes of its composition while underlying their least advantageous attributes . Composites have been widely used in various application starting from aerospace , Manufacturing plants , Electrical equipment's , Marine , Automotive ,Civil Infrastructure , Corrosive Environment’s ,Whereas the Epoxy which are the cured components of two chemical functional group namely polyepoxides …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 1, 2021 Read article
-
International Journal of Manufacturing and Materials Processing
Abstract: Friction and wear resistance were studied on SiC-based novel ceramic composite for applications in advanced automotive braking systems. In the present work, SiC-based ceramic composite was prepared by solid-state reaction synthesis route using a fine powder of precursors. The product was investigated for wear rate under different load conditions in the range from 10N to 70N and speed conditions in the range from 0.13 m/s to 0.52 m/s. The present …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 1, 2021 · pp. 14–24 Read article
-
Review on Recent Trends in Laser Assisted Machining of Hard to Cut Materials
Abstract: Laser-assisted machining (LAM), an alternative method of fabricating hard-to-machine materials, like ceramics, composites, Titanium alloy, Nickel based alloy are being developed and widely utilized in aerospace, automotive, medical and nuclear industries due to their special properties. These materials posing many challenges when machined with the help of Conventional methods of machining. Conventional methods of machining these materials are found to be uneconomical. Among the various external energy assisted machining methods, …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 2, 2021 · pp. 49–57 Read article