International Journal of Composite and Constituent Materials

Mechanical Behavior of AA7075/Glass Fiber Reinforced Polymer Composites

  1. Rajshekhar Ghogge ✉
  2. Kenchamarappa .
  3. Santhosh Kumar A.S
  4. Pruthviraj R.D

Abstract

This paper reports on the mechanical properties of As-cast and heat-treated AA7075 polymer composites reinforced with glass fibers from 1 to 5 wt%. The polymer composites were fabricated using the Compo casting method, in which short glass fibers were introduced into the vortex created in the molten alloy through an impeller rotated at 500 rpm. The molten mass was thoroughly stirred and poured into permanent molds and squeezed under pressure. The specimens were heat treated at 575°C for 1, 2, 3, and 4 h. The tests on the As-cast polymer composites revealed that as the glass content in the polymer composites was increased, the ultimate tensile strength (UTS), compressive strength, and hardness of the composite increased, while the ductility and impact strength were decreased. Heat treatment was found to improve significantly the ductility, compressive strength, and impact strength, while the hardness and UTS were reduced. This paper discusses the behavior of these polymer composites.

Keywords

References (18)

  1. A.M. Samuel and F.H. Samuel, Foundry Aspects of Particulate Reinforced Aluminium PCs: Factors Controlling Composite Quality, Key Engineering Materials, G.M. Newaz, H. Neber-Aeschbacher, and F.H. Wohlbier, Ed., Trans Tech Publications, Switzerland, 1995, p. 65–98
  2. I.A. Ibrahim, F.A. Mohammed, and E.J. Lavernia, Particulate Reinforced Metal Matrix Polymer composites, J. Mater. Sci., Vol 26, 1991, p.
  3. D.J. Lloyd, Particle Reinforced Aluminium and Magnesium Matrix Polymer composites, Int. Mater. Rev., Vol 39 (No. 1), 1994, p. 1–21
  4. H.D. Huda, M.S.J. Hashmi, and M.A. El-Baradie, PCs: Materials, Manufacturing and Mechanical Properties, Key Engineering Materials, G.M. Newaz, H. Neber-Aeschbacher, and F.H. Wohlbier, Ed., Trans Tech Publications, Switzerland, 1995, p. 37–64
  5. W.H. Hunt, T.M. Osman, and J.J. Lewandowski, J. Met., Vol 45, 1993, p. 30
  6. P.M. Singh and J.J. Lewandowski, Metall. Trans., Vol 24A, 1993, p. 2531
  7. C.M. Friend, The Effect of Matrix Properties on Reinforcement in Short Alumina Fiber-Aluminium Metal Matrix Polymer composites, J. Mater. Sci., Vol. 22, 1987, p. 3005.
  8. Y.T. Zhu, G. Zong, A. Manthiram, and Z. Elizer, Strength Analysis of Random Short Fiber Reinforced Metal Matrix Composite Materials, J. Mater. Sci., Vol 29, 1994, p. 6281
  9. A. Alahelisten, F. Bergman, M. Olsson, and S. Hogmark, On the Wear of Aluminium and Magnesium Metal Matrix Polymer composites, Wear, Vol 165, 1993, p. 221
  10. P.K. Rohatgi, B.C. Pai, and S.C. Panda, Preparation of Cast Aluminium Silica Particulate Polymer composites, J. Mater. Sci., Vol 14, 1979, p. 2227
  11. S.R. Nutt and R.W. Carpenter, Non-equilibrium Phase Distribution in Al-Glass fiber Polymer composites, Mater. Sci. Eng., Vol 75, 1985, p. 169
  12. S.R. Nutt, Interfaces and Failure Mechanisms in Al-Glass fiber Polymer composites, Proc. Conf. Interfaces in Metal-Matrix Polymer composites, A.K. Dhingra and S.G. Fishman, Ed., TMS, Warrendale, PA, March 1986, p 157
  13. W. Smith, Structures and Properties of Engineering Alloys, 2nd ed., McGraw-Hill, New York, 1993, p. 561–568
  14. M.J. Barber and P.E. Jones, A New Family of Foundry Alloys, Foundry Trade J., Vol 17, 1980, p. 114
  15. P.P. Lee, T. Savaskan, and E. Laufer, Wear, Vol. 117, 1987, p. 79
  16. Sukumar, M.S., Anand Babu, K., Venkataramaiah P. 2014. Exploration of mechanical behaviour of Al2O3 reinforced aluminium metal matrix composites Elixir Mechanical Engineering, 72, 25462–25465.
  17. Shorowordi, K.M., Laoui, T., Haseeb, A.S.M.A., Celis, J.P., Croyen, L. 2003. Microstructure and interface characteristics of B4C, Sic and Al2O3 reinforced Al matrix composites: a comparative study, Journal of Processing Technology, 142, 738–743.
  18. Kumar, T., Ramana, K.V., Choudary. R.B. 2018. Spectroscopic characterization of mechanically synthesised MoO3/Tio2 Composite Nano Powders.

Read more of it

Subscribe to one journal or build your own list of several. One invoice, one payment, access for a full year.

Subscribe to journals →

Publish your article

Peer-reviewed journals across every subject, with open access options. Send your manuscript to the right editor today.

Publish with us → Calculate your APC
Support