Search
138 articles for “Corrosion”
-
ENHANCEMENT OF MECHANICAL PROPERTIES OF ALLOY 61S BY REINFORCING NANO COMPOSITES
Abstract: During recent decades, a lot of interest had shown in the materials production with nano sized grains. Especially, the aluminum alloys and its composites are widely used for demanding structural applications due to combination of corrosion resistance, formability, weldability and, mechanical properties. The demand for toughness, higher strength and, strength and weight ratio of aluminum alloys for the structural application is ever growing owing to the increasing importance of achieving …
Published in International Journal of Metallurgy and Alloys · Vol. 5, Issue 2, 2019 · pp. 18–36 Read article
-
MANUFACTURING AND TESTING OF CNT BLENDED NAVAL BRASS
Abstract: The Utilization of advanced technologies increased the scope of producing new materials drastically .as a result wide spectrum of nanomaterials are being produced these materials are manufactured as per the desired properties in the final material /composite. The aim of this study is to investigate the effect of CNT (Carbon Nano Tubes) reinforcement into naval brass (Cu-CNT 60%, Zinc 39%, and Tin 1%) naval brass is widely applied in the …
Published in International Journal of Metallurgy and Alloys · Vol. 6, Issue 2, 2020 · pp. 7–11 Read article
-
Ability of Metallic Materials to Resist Surface Damage Induced by High-temperature Action of Air or other Gaseous Mediums
Abstract: The features of the oxide layer scale that forms on the metal's surface and limits gas penetration into the metal, limiting the growth of gaseous corrosion, influence a metal's or alloy's oxidation resistance in an oxidising atmosphere. The rise in weight of sample being tested (due to oxygen uptake by the metal) or even the weight loss after removing the scale from the sample's surface, related to a unit surface …
Published in International Journal of Metallurgy and Alloys · Vol. 8, Issue 1, 2022 · pp. 16–21 Read article
-
An Extensive Overview of Al-Mg-Si Alloy’s Electrochemical Behavior
Abstract: This review emphasizes on the effects of microstructure and alloying components on the electrochemical behavior of Al-Mg-Si alloys used as sacrificial anodes. The presence of alloying elements hinders surface film formation on aluminum, while microstructural factors such as grain size distribution and precipitate volume fraction influence alloy properties. The Al-Mg-Si phase diagram and the presence of the Mg2Si phase are also discussed, highlighting the effects of Mg and Si solubility. …
Published in International Journal of Metallurgy and Alloys · Vol. 9, Issue 2, 2023 · pp. 1–11 Read article
-
Fabrication, Microstructure and Mechanical Behavior of Aluminum Alloy (LM-13) Reinforced with Nano-ZrO2 Particulate Chilled Nano-Metal Matrix Composites (CNMMCs)
Abstract: In the present research, aluminum alloy (LM13) Metal Matrix Composite (MMC) is prepared by stir casting technique and is reinforced with ZrO2 particulates in the weight percent ranging from 3 wt.% to 12 wt.% in the steps of 3 wt.%. The reinforcement i.e., ZrO2 particle size added varies between 100–200 nm. The resulting CNMMCs are solidified under the influence of copper chill of 25 mm thickness to study the effect …
Published in International Journal of Nanomaterials and Nanostructures · Vol. 6, Issue 2, 2020 · pp. 17–30 Read article
-
Drilling of Fibre Reinforced Plastics (FRPs) Materials: A Literature Survey
Abstract: The use of polymer composite materials has increased rapidly over the last decade and the numbers of papers for the machining of these materials has also increased. The aim of this paper is to present a literature survey on the resins, properties, the superiority of the hole produced in drilling of the fibre reinforced plastics (FRPs), different techniques used to detect the defects in composite structures that may be caused …
Published in International Journal of Composite and Constituent Materials · Vol. 1, Issue 1, 2015 · pp. 14–31 Read article
-
An Evaluation of Cracks Repairing Techniques in Metals
Abstract: Cracks are surface that develop in a material. Dissemination energy derived from mechanical, thermal, chemical, and metallurgical effects, or a grouping of these may affect crack beginning and growth. Numerous types of cracks exist in metals and can be characterized as grinding, solidification, cooling, crater, machining tears, plating, centerline, pickling, heat treatment, fatigue, creep, stress corrosion and hydrogen cracks. Cracks can grow and lead to complete fracture of the component …
Published in International Journal of Composite Materials and Matrices · Vol. 3, Issue 1, 2017 · pp. 9–15 Read article
-
Market Assessment of Polymer Matrix Composites
Abstract: Polymeric composition compound with a plasticizer or very low proportion of pigment or processing aids are nonordinary consider as a composition the goal is to improve strength stiffness or toughness or dimensional stability by embedding particles in matrix or binding phase. Polymer-matrix composites are valued in the aerospace industry for their stiffness, lightness, and heat resistance. They are fabricated materials in which carbon or hydrocarbon fibres (and sometimes metallic strands, …
Published in International Journal of Composite Materials and Matrices · Vol. 3, Issue 1, 2017 · pp. 16–22 Read article
-
Finite Element Analysis of Composite Tube
Abstract: Abstract – In many industries, composite tubes are preferable than other materials, like, aluminum, steel, wood, iron. The durability, strength, stiffness, weather and corrosion resistance of the tubes are required properties in industries. It is fabricated in several layers depending on their functions. In this study, composite tube is modeled using ANSYS software by changing material properties and layer orientation. ANSYS can predict results before fabricating composite sample. The meshed …
Published in International Journal of Composite Materials and Matrices · Vol. 5, Issue 2, 2019 · pp. 48–59 Read article
-
Recent Progress of Post-reactor and Reactor-made Polypropylene-based Thermoplastic Elastomers
Abstract: The global market for thermoplastic elastomer (TPE) is growing rapidly owing to the rising demand from the packaging, automotive, healthcare, construction, electrical, electronics and other sectors. Significant progress has been made in the last few decades in the development of different TPE. Polypropylene being low-cost, corrosion resistance, better mechanical properties and readilyavailable, has attracted several researchers to develop polypropylene based thermoplastic elastomers (PP-TPE). This review focuses on recent advancements in …
Published in International Journal of Composite Materials and Matrices · Vol. 8, Issue 2, 2022 · pp. 1–18 Read article
-
Flexural Properties of Vetiver Fiber Reinforced Polyethylene Composite are Affected by Processing Parameters
Abstract: Fiber reinforced polymer composites have long been influential in a variety of applications due to their great particular strength and modulus. Vetiver fiber (VF)/thermoplastic composites are an alternative material for solving the environmental pollution problem related to synthetic polymers. The benefits of natural fibers (such as coir, jute, vetiver, calotropis gigantea, flax, hemp, kenaf, etc.) over traditional reinforcing fibers (glass and carbon fiber) are their easy obtainability, renewability, non-corrosive nature, …
Published in International Journal of Composite Materials and Matrices · Vol. 9, Issue 1, 2023 · pp. 12–20 Read article
-
Synthesis Innovative Cyclic Formazan Compounds for the First Time and Evaluation of Their Biological Activity
Abstract: The research included the invention of cyclic formazan compounds for the first time in this research that carried out in April 2021, where the usual formazan compoundswere previously attended, but in the current research we attended the cyclic formazan compounds as innovative compounds and after that they were diagnosed by reliable chemical means of measurement, that provided vibrant indication of theirchemical constructions via numerous technical apparatuses similar (FT IR-Bands, 1H.NMR-Peeaks, …
Published in International Journal of Polymer Science and Engineering · Vol. 7, Issue 2, 2021 · pp. 5–14 Read article
-
Reviewing the Evolution of Nanotechnology in the Oil and Gas Sector: Focus on the Utilization of Silica Nanoparticles
Abstract: Nanotechnology is advancing notably in the oil and gas sector, with its applications demonstrating substantial progress. The use of nanoparticles in various aspects of the industry has shown promise in addressing challenges and improving efficiency. Nanotechnology is finding applications across multiple facets of the oil and gas industry, encompassing areas such as the development of drilling and hydraulic fracturing fluids, cementing for oil wells, improved oil recovery techniques, corrosion prevention, …
Published in International Journal of Polymer Science and Engineering · Vol. 9, Issue 2, 2023 · pp. 30–36 Read article
-
Optimization of Process Parameters of GMAW for Penetration, Toughness and Tensile Strength by using Taguchi Method
Abstract: Aluminum and its alloys are having variety of applications in Aircraft, food processing etc. Moreover; the use of Aluminum and its alloys are increasing day by day due to its specific properties, like light weight, high strength, and excellent corrosion resistance. However; the present study is planned to analyze and optimize the aluminum weld joint characteristics like tensile strength, penetration and toughness by using Gas Metal arc welding (GMAW) welding. …
Published in International Journal of Mechanics and Design · Vol. 5, Issue 1, 2019 · pp. 1–9 Read article
-
Hardened Steel an Appliance with Low Degeneration
Abstract: Combination of high hardness, toughness, and strain hardening capacities with reasonable ductility have privileged Hadfield steel in sectors such as mining, transportation, military, agricultural and earthmoving equipment. Micro- porosities formation during casting by last solidifying liquids at inter-dendritic spaces in directional solidification have been insidious crack initiators during service exposure. Particulate penetration resistant wear part surfaces for secondary and tertiary crushers are found to add chromium and vanadium prone to …
Published in International Journal of Mechanics and Design · Vol. 5, Issue 2, 2019 · pp. 56–60 Read article
-
Risk Assessment And Analysis In A Chemical Industry
Abstract: Chemical manufacturing sector in India is well established and has recorded a steady growth in the overall industrial scenario .The chemical and the allied industries are among the faster growing segments of Indian industry. The risks associated with the chemical industry are commensurate with their growth. Apart from their utility, chemicals have their own inherent properties and hazards like flammable, explosive, toxic or corrosive etc. Several major accidents had occurred …
Published in International Journal of Manufacturing and Materials Processing · Vol. 2, Issue 1, 2016 · pp. 57–64 Read article
-
Multi-objective Optimization of Weld Bead Geometry of Micro-plasma Arc Welded Titanium (Ti–6Al–4V) Alloy Sheets Using TOPSIS
Abstract: Titanium alloys are used in the manufacturing of aero engine components for their attractive, combined properties such as lightness, good strength-to-density ratio, corrosion resistance. In the present paper, titanium (Ti–6Al–4V) alloy sheets are butt welded using micro-plasma arc welding. Peak current, base current, pulse rate, and pulse width are considered as weld input parameters and weld bead geometry parameters, namely front width, back width, front height, back height, are considered …
Published in International Journal of Manufacturing and Materials Processing · Vol. 5, Issue 1, 2019 · pp. 37–48 Read article
-
Analysis of Mechanical Attributes of Nano clay Reinforced Polymer Composites
Abstract: Composite material provide a Higher and unique mechanical and physical attributes because of its combines the most unique attributes of its composition while underlying their least advantageous attributes . Composites have been widely used in various application starting from aerospace , Manufacturing plants , Electrical equipment's , Marine , Automotive ,Civil Infrastructure , Corrosive Environment’s ,Whereas the Epoxy which are the cured components of two chemical functional group namely polyepoxides …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 1, 2021 Read article