Search
1891 articles for “ABS”
-
Finite Element Analysis of Composite Pressure Vessel with Non-Geodesic Fiber Trajectory In view of Friction Factors on Cylinder and End Domes
Abstract: Composites are materials created by dissimilar materials with a view to improve the properties or to create materials with desired properties. Progressive Fiber Polymer Composites have developed as an essential class of industrial materials for load carrying applications with well-rounded properties for many industrial and social applications. Structures like pressure vessels, pipes and motor casings made-up of Filament Winding technology are widely used in aerospace applications. Conventionally, pressure vessels were …
Published in International Journal of Composite Materials and Matrices · Vol. 7, Issue 2, 2021 · pp. 9–21 Read article
-
Demonstration of Adsorbent Morphology of Different Particle Size for Petroleum Hydrocarbon Treatment in Packed Bed
Abstract: The choice of plantain stem, banana stem and palm oil fibre prepared for treatment of water medium polluted with petroleum hydrocarbon was monitored in a packed bed unit. The raw materials (plantain and banana stem as well as palm oil fibre) were room and sun dried and processed to obtained different particle size of 50, 150 µm and 200 µm. The raw material after processed was used as an adsorbent …
Published in International Journal of Composite Materials and Matrices · Vol. 9, Issue 2, 2023 · pp. 13–19 Read article
-
Review Study on Experimental Investigation of Heat Transfer Using Al2O3 and CuO Nanoparticles with Water as Base Fluid Through Circular Tube of Heat Exchangers
Abstract: A colloidal mixture of nanometric particles (<100 nm) in a base liquid called nanofluid, which is the new generation of heat transfer fluid for various heat transfer applications where the transport characteristics are substantially higher than the base liquid. This review summarizes and analyzes the empirical correlations for the effective thermal conductivity and the dynamic viscosity of the nanofluid on the basis of experimental data and the theoretical model available …
Published in International Journal of Mechanics and Design · Vol. 3, Issue 2, 2017 · pp. 17–23 Read article
-
Finite Element Analysis of Rectangular Plate of S460J2 With Multiple Circular Holes
Abstract: Stress concentration is the main root cause of failure of multi-hole plates in bi-axial loaded conditions. Therefore it is essential to study such Stress Concentration Factors (SCF) to achieve the failure criteria. The method used for analysis is FE analysis. The main cause of increment in the stress is the geometrical irregularity, which may be caused by the various machining operations. Some kind of operations also requires such irregularity for …
Published in International Journal of Mechanics and Design · Vol. 4, Issue 2, 2018 · pp. 7–14 Read article
-
CFD Analysis on Exhaust System of a Car
Abstract: The pollution and global warming is due to air pollution. It is to be noted that air pollution is mainly caused by the toxic gases from the exhaust of the automobiles. Only 30% of the fuel is converted into energy source to run the engine remaining 70% of fuel is of un-burnt hydrocarbon, carbon monoxide and nitrogen oxides. From modified catalytic converter, noise level will decrease. Here, the performance of …
Published in International Journal of Mechanics and Design · Vol. 5, Issue 1, 2019 · pp. 38–50 Read article
-
Design and Fabrication of Trammel Balls
Abstract: Transportation of water plays a vital role in the survival of a growing population. If the scarcity of water is one major issue, transportation of water using tankers have their own share. Water in a partially filled container, when induced with external energy (motion), generates slosh and surge. Both slosh and surge effects work as a resistive factor during transportation. To eliminate the same, few holes are drilled at pre-desired …
Published in International Journal of Mechanics and Design · Vol. 5, Issue 2, 2019 · pp. 24–39 Read article
-
Hardened Steel an Appliance with Low Degeneration
Abstract: Combination of high hardness, toughness, and strain hardening capacities with reasonable ductility have privileged Hadfield steel in sectors such as mining, transportation, military, agricultural and earthmoving equipment. Micro- porosities formation during casting by last solidifying liquids at inter-dendritic spaces in directional solidification have been insidious crack initiators during service exposure. Particulate penetration resistant wear part surfaces for secondary and tertiary crushers are found to add chromium and vanadium prone to …
Published in International Journal of Mechanics and Design · Vol. 5, Issue 2, 2019 · pp. 56–60 Read article
-
Solar Assisted Dehumidification Systeme Using Liquid Desiccant (Fabrication)
Abstract: A dehumidifier is a device which removes moisture from air and makes the air dry. A solar assisted dehumidifier using liquid desiccant has advantages of being solar powered as well as use of liquid desiccant increases the efficiency and minimizes the health hazards.
Published in International Journal of Mechanics and Design · Vol. 6, Issue 1, 2020 · pp. 12–16 Read article
-
Design and Performance Testing of Brown Grass Flower Broom Reinforced Composites
Abstract: Engineering materials are classified into many varies and composites are those which are finding their role in all modern day engineering applications. Composite materials are materials made of two basic components, polymer resins and fibers. It combines the physical properties and high mechanical properties of the fiber, as well as the appearance, adhesion and performance of the polymer. Here, we prefer brown grass flower brooms as our main fiber to …
Published in International Journal of Mechanics and Design · Vol. 6, Issue 2, 2020 · pp. 34–37 Read article
-
LATTICE-BASED CELLULAR STRUCTURE DESIGN STRATEGY
Abstract: This research article has examined the objective of investigating the design processes orapproach for CAD modeling using open-source 3D modeling and graphics tools. Thisresearch focuses on CAD modeling and the numerous challenges and concerns associatedwith developing micro-lattice structures for the metal additive manufacturing process usingDFAM guidelines. These structures have been built for metal AM employing 3D-periodicregular and FGLSs (homogenous and heterogeneous) with varied unit-cell types and sizes.Another purpose of this …
Published in International Journal of Mechanics and Design · Vol. 8, Issue 2, 2022 · pp. 7–14 Read article
-
Weldability of Ferrous Metals
Abstract: The weldability of various steels and cast iron were reviewed. Weldability of steel/cast iron refers to the maximum hardness of the HAZ and cold cracking susceptibility of welds. Many researches on weldability of ferrous metals were discussed; research on weldability of high carbon steel and white cast iron are limited. Most researchers inclined to hardness and tensile test of weldment of ferrous metals; researches on creep, fatigue, damping capacity, impact …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 2, 2020 · pp. 14–21 Read article
-
A Laboratory Test Methodology Development For Validating 4wd Front Axle Spindle
Abstract: Tractor is a vehicle specially designed for performing various agricultural and off-road applications. With the increasing popularity of 4WD tractor, front axle design & validation has become critical. 4WD front axle spindle is a part of 4WD front axle assembly. The power transfers from engine to spindle through input shaft, differential unit, intermediate shaft and King pin shaft. Front axle spindle failure was observed during field testing. No component level …
Published in International Journal of Manufacturing and Materials Processing · Vol. 9, Issue 2, 2023 · pp. 23–31 Read article
-
The Effect of Air Bubbles Injection into a Shell and Coiled Tube Heat Exchanger: A Review
Abstract: In present study, a shell and coiled tube heat exchanger has been mathematically studied. The helically coiled tube and the effects of on thermal characteristics of heat exchanger will be proposed in this study. CFD analysis on ANSYS software will be performed. Shell tube carrying cold water, helical coil containing hot water and U shaped hollow pipe carries air. Thermal properties and its effect has been considered in the study.
Published in International Journal of Computer Aided Manufacturing · Vol. 3, Issue 2, 2017 · pp. 34–42 Read article
-
Cooling and Heating Effect of Geothermal Energy and Its Thermal Analysis Using Air as a Flow Medium
Abstract: Geothermal energy is one of the renewable sources of energy, which exists free in the environment. The main concept of a geothermal energy is the thermal energy of the ground which is used for cooling and heating. Here, air is used as a flow medium. The flow medium gets cool in the summer and gets heated in the winter due to the temperature difference between the flow medium and underground …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 18–32 Read article
-
Computational Simulation of Continuous Centrifugal Machine using Computational Fluid Dynamics
Abstract: In this paper, the centrifugal machine which is used in a sugar industry has been analysed. The centrifugal machine is used for the separation of the molasses and the sugar crystals from the massecuite. The objective behind the analysis of the flow in the centrifuge is to achieve the reduction in the separation process time using the Computational Fluid Dynamics and to increase the tonnes/hour output of the sugar. The …
Published in International Journal of Computer Aided Manufacturing · Vol. 5, Issue 1, 2019 · pp. 1–8 Read article
-
INVESTIGATE THE BULGING EFFECT OF METALLIC SOLID CYLINDER UNDER COLD UPSETTING USING FINITE ELEMENT ANALYSIS
Abstract: Friction is an integral part of metalworking and manufacturing processes due to the relative motion and forces continually acting on tools, dies, and workpieces. Friction both raises the effort and consumes energy. However, measuring friction is not straightforward and cannot be considered an independent parameter. In many metal-forming procedures, the impact of friction is just as crucial as other quantifiable factors. Various methods have been used to estimate friction, assuming …
Published in International Journal of Computer Aided Manufacturing · Vol. 8, Issue 2, 2022 · pp. 7–18 Read article
-
SeamlessScan: Transforming Grocery Checkout with a Next- Generation Billing Solution
Abstract: The supermarket is a type of retail store that sells food primarily. A grocery store sells food in bulk. It is not wise to purchase food from a roadside vendor given the rise in global pollution. Operating a grocery shop properly involves agreat deal of obligation, whether you are in charge of a small, independently owned store as one that is a part of a bigger company. The grocery store …
Published in International Journal of Computer Aided Manufacturing · Vol. 9, Issue 1, 2023 · pp. 22–28 Read article
-
A Short Note on I.C. Engine and Its Components
Abstract: This article presents a brief description of IC engine and its components. Working principle is also explained which conveys a clear idea about efficiency that it starts immediately without much efforts and has higher efficiency than the external combustion engine. Other aspect of IC is that it is portable because of its light weight and compact size. Since it is safer to use, IC engine is commonly preferred for various …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 1, Issue 2, 2015 · pp. 12–15 Read article
-
Renewable Energy Technologies for Future and Sustainable Development
Abstract: People are relying upon oil for primary energy and this will continue for a few more decades. Other conventional sources may be more enduring but are not without serious disadvantages. The renewable energy resources are particularly suited for the provision of rural power supplies and a major advantage is that equipment such as flat plate solar driers, wind machines, etc., can be constructed using local resources. Without the advantage results …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 4, Issue 2, 2018 · pp. 11–29 Read article
-
Waterjet Peening Process: A Review
Abstract: Water jet machining is few of the most adaptive and unconventional type of machining with huge advantage over the conventional type machining. Depth of cut measurement is a vital component in evolution of completely automated Abrasive Waterjet (AWJ) machining system. While cutting Ti-6Al-4V under waterjet, it is important to measure the depth of cut of material at the instant of cutting. This is a major drawback of Water Jet Machining …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 6, Issue 1, 2020 · pp. 12–14 Read article