Search
1495 articles for “work”
-
Design and Fabrication of Flower Plucking Device
Abstract: Flower plucking device is one which cuts the flowers and collects them without causing any damage to the flowers. The device is extendable and can be used to cut the flowers at a height of around 3m from the ground level. The device consists of a collecting bucket which is mounted on a handle and the thread is provided for actuating the scissor or cutter, the thread is moves on …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 2, 2020 · pp. 8–13 Read article
-
Six Sigma (DMAIC) Approach to Optimise Operation Variables in High Pressure Die Casting
Abstract: Components manufactured by High Pressure Die Casting (HPDC) typically have excellent mechanical and metallurgical properties, and the process generally preferred for the manufacture of high-value-added products. This research paper focuses on the implementation of the Six Sigma philosophy to optimize the variables of the HPDC manufacturing process. As a systematic outline for quality improvement and achievement business excellence, the Six Sigma philosophy has become the model of the industrial world …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 2, 2020 · pp. 22–51 Read article
-
To Enhance Wear Resistance of Cast Iron Using Thermal Spray Coating Techniques
Abstract: In the present research work, an experimental study is being carried out to evaluate and enhance wear resistance of cast iron using thermal spray coating techniques. For this work, coating materials used were WC–Co–Cr and Ni–Cr in powdered form, and the coating was done by D-gun (detonation-gun) method. Wear behavior was investigated using pin-on disc apparatus at 30,40 and 50N on both coated and uncoated samples of cast iron, and …
Published in International Journal of Manufacturing and Materials Processing · Vol. 6, Issue 1, 2020 · pp. 1–5 Read article
-
Lean Conceptual Model for SMEs using 5S
Abstract: Lean manufacturing is a systematic framework for eliminating waste from a manufacturing system, or value stream, without sacrificing productivity Literature related to work shows that there are various sets of tools or techniques that have been adopted at a certain degree across firms according to their own manufacturing capacity and available resources needed for implementation of lean techniques. This paper describes the implementation of ‘5S’ as lean tool on machine …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 2, 2021 · pp. 43–48 Read article
-
A Study on Effect of Polarity on Mechanical Properties in Saw Process
Abstract: Welding is one of the most common fabrication techniques which is extensively used to obtain desirable quality welds for intended application in various structural components. The invariable importance of welding processes has been very well realized since long times ago, therefore till nowadays there is hardly any sector of human life which has not been benefited from applications of welding. Apart of quality of flux and welding parameters, welding processes …
Published in International Journal of Manufacturing and Materials Processing · Vol. 7, Issue 1, 2021 · pp. 1–6 Read article
-
Multi Criteria Optimization in Drilling Process of Glass Fibre Reinforced Polymer Using Grey Based Taguchi Analysis
Abstract: The current work uses multi-response Taguchi GRA to analyse and optimise the drilling variables for a modified glass fibre reinforced polymer (GRRP). The L27 orthogonal array design was used to carry out the experiments. The filler material used in this study is hematite ore (Fe 2 O 3 ) particles of 75-150µm, E-Glass fiber of 300 GSM, and LapoxL-12 resin has been used to fabricate the modified GFRP composite laminates. …
Published in International Journal of Manufacturing and Materials Processing · Vol. 8, Issue 2, 2022 · pp. 6–16 Read article
-
Design and Finite Element Analysis of Refractory Boiler Shell for Optimum Weight
Abstract: This paper deals with the stress analysis of boiler shell with refactory. By using finite element method, a stress analysis has been carried out under the application of pressure at the inner surface of boiler shell. Von-Mises stresses and maximum shear stresses are found. Currently we are working on the condition in order to find temperature distribution so that it will be helpful for us to get thermal analysis and …
Published in International Journal of Computer Aided Manufacturing · Vol. 4, Issue 1, 2018 · pp. 48–54 Read article
-
Software Numerical Simulation on Earth Tube Heat Exchanger Where Air as A Flow Medium
Abstract: Renewable energy is free in nature and it must be brought into application. Due to use of air conditioning and its refrigerants global warming is a serious issue. Renewable energy is the main concept of an earth tube heat exchanger, which uses the thermal energy of the ground for cooling and heating of the fluid medium. Here, air is used as fluent working medium. The air cools in summer and …
Published in International Journal of Computer Aided Manufacturing · Vol. 6, Issue 1, 2020 · pp. 19–45 Read article
-
New Proposal and Design to Add Retarders in Automotive
Abstract: Today, the issue of occupant safety is one of the most important issues in the automotive industry. Oneof the most important factors in improving the braking performance of cars has been considered in thearticle is the use of auxiliary brakes. Among the common auxiliary brakes that were proposed in carsand used by experimental test, we can mention retarder brakes. Used in heavy vehicles in passengercars will also be widely used …
Published in International Journal of Computer Aided Manufacturing · Vol. 7, Issue 1, 2021 Read article
-
Thermal Modeling and Optimization of Irreversible Cogeneration Power Plant
Abstract: This paper aims at studying the cogeneration system coupled with outer heat reservoir of finite heat capacity and comprises of both external as well as internal irreversibility. External irreversibility is due to the finite-rate heat transfer between the working fluid and heat reservoirs while internal irreversibility is due to heat dissipation of working fluid. Both types of irreversibility are involved in the study on introducing an internal irreversible parameter which …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 1, Issue 2, 2015 · pp. 01–11 Read article
-
Review on Vibration Problems in Turbomachinery
Abstract: Vibration suppression of turbomachinery is an important engineering problem. Vibration caused by mass imbalance is a common problem in rotating the turbomachinery systems. Imbalance occurs if the principal axis of inertia of the rotor is not coincident with its geometric axis. Higher speeds cause much greater centrifugal imbalance forces, and the current trend of rotating equipment toward higher power density clearly leads to higher operational speeds. In this paper, a …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 1, Issue 2, 2015 · pp. 54–57 Read article
-
Design and Analysis of Multicylinder Four Stroke Spark Ignition Axial Engine (Duke Engine)
Abstract: Engine is a very important component in automobiles and it is act as a prime mover. The engine transmits power to the road wheels trough linkages (Clutch, gearbox, propeller shaft and differential) against to the self-weight of the vehicle and external load, which results the engine components undergo stressed. The engine components also exposed to the heat so that the thermal stress are induced. Based on the above said points …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 3, Issue 1, 2017 · pp. 14–39 Read article
-
An Overview on Sterling Engine
Abstract: This paper presented an overview on Stirling engine, working principle and history of sterling engine. Power and efficiency of the engine must be not lower than their averaged values for the same engine working in unsteady conditions. This paper represents different researches on sterling engine and its modification and use from past to present.
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 4, Issue 2, 2018 · pp. 48–52 Read article
-
Air-Powered Cars
Abstract: This paper is reporting an experimental investigation of an engine driven by compressed air. The compressed-air engine is modified from a four-stroke working engine to two-stroke working engine (power and exhaust) by modification of cam-gear system. The project was successfully manufactured and tested. Experimental results were carried out on this modified engine to find out its performance characteristics like brake power, mechanical efficiency, indicated power, torque, etc. It should be …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 5, Issue 1, 2019 · pp. 41–44 Read article
-
Synthesis and Characterization of Biodiesel from Animal Fat
Abstract: Biodiesel, an alternate and ecologically acceptable substitute for the conventional fuel, is usually produced from a wide range of edible vegetable oils, which are normally used for human consumption and whose prices are expected to increase in future. In this regard, reliable and low-cost raw materials have increasingly drawn interest for biodiesel production, such as by-products of the meat processing industries or waste animal fats. In present work biodiesel production …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 5, Issue 2, 2019 · pp. 45–54 Read article
-
CFD Simulation on Ground Tube Heat Exchanger using Copper and Aluminum as Tube Material
Abstract: Renewable energy is free in nature and it must be brought into application. Due to use of air conditioning and its refrigerants global warming is a serious issue. Renewable energy is the main concept of an earth tube heat exchanger, which uses the thermal energy of the ground for cooling and heating of the fluid medium. Here, air is used as fluent working medium. The air cools in summer and …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 6, Issue 2, 2020 · pp. 49–74 Read article
-
Experimental investigation on single cylinder 4-stroke diesel engine using nanofluids as a coolant to compact the system
Abstract: Recent power sectors associated with an internal combustion engine had a crucial challenge to reduce the size and weight of the thermal management system of internal combustion engines. This work aims to reduce the size and weight of the internal combustion engine cooling system by utilizing particular types of working medium as a coolant in place of traditional ones. In this study, the effects of water base CuO nano-coolant on …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 7, Issue 1, 2021 · pp. 12–25 Read article
-
Development and Modification of 2-Stroke IC Engine
Abstract: Today world is concerned more about saving the environment, everywhere precautionary measures have been taken up to reduce pollution. Major amount of air pollution is caused by mechanical animals running on roads; they contribute to most of the air pollution, hence, engineers today to focus on how to build an eco-friendly engine which can reduce the pollution caused by vehicles. A compressed air engine works on air as fuel to …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 7, Issue 1, 2021 · pp. 8–11 Read article
-
Experimental Energy Analysis of R134a and HC (Propane + Butane) as a Refrigerant in Domestic Refrigerator
Abstract: This paper presents an experimental and numerical study for identical household refrigerator using hydrocarbon butane/propane mixture as a drop replacement for R134a. GWP of R134a is very high (i.e.1300) as compared to hydrocarbon butane/propane mixture (i.e. 8). The household refrigerator basically designed to work with R134a. In this paper the cooling performance for both refrigerants was experimentally measured and then compare for suction temperature, temperature after condensing, temperature after cooling …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 8, Issue 1, 2022 · pp. 25–33 Read article
-
Heat Transfer Performance in an Internally Dimpled Tube Heat Exchanger Composed of Various Materials Examined Using CFD: A Review
Abstract: A review of the most important findings for thermal enhancement on circular pipe is presented, the focus is on the heat transfer and thermal gradient in these heat exchangers. The use of circular dimpled pipes, surfaces, and other techniques to promote heat transmission has been the subject of several studies in the past. Reviews are conducted on a sizable number of research papers pertaining to computational and experimental investigations. Various …
Published in International Journal of I.C. Engines and Gas Turbines · Vol. 9, Issue 2, 2023 · pp. 30–40 Read article